10 Tips You Should Know About Air Tools
1. A smaller air tool doesn’t mean it uses less air
A small hand-held air grinder. Still requires 8 CFM of airflow.
Just because an air tool fits in your hand doesn’t mean it consumes less air. Spinning tools require significant airflow to drive their internal components. Smaller models may use slightly less than heavier ones, but they can still quickly drain a direct-drive compressor. Always check the tool’s specifications—MAC-AFRIC™ tools list the required CFM or l/min, helping you match the tool with the correct compressor size.
2. You need a compressor that’s 20% larger than you think
An example of a 2.2kW Belt Driven Air Compressor – a solid starting point for most air tools.
Balancing budget and performance when buying a compressor can be tricky. You need to consider session length, tool usage, and the compressor’s duty cycle (often 60–80%). That means 10 minutes of use may require 4 minutes of cooling.
Add 20% to your tool’s CFM rating to prevent your compressor from overworking. This ensures efficient performance under heavy use. We offer options from small units to heavy-duty industrial ones.
3. DIY compressors aren’t workshop machines
A direct-drive compressor. No belt – ideal for occasional DIY use only.
Budget DIY compressors aren’t built for high-volume or long-term workshop use. They have shorter duty cycles and wear faster. Invest in a belt-driven or semi-industrial unit for regular tasks.
4. Air pressure matters
Attach a regulator to most air tools or compressors to fine-tune pressure.
Most tools don’t require full compressor pressure (usually 8 bar). Excess pressure can damage tools and reduce lifespan. Always use the pressure marked on your tool for best results—especially true for spray guns.
5. Using air tools without a filter is risky
Water traps help prevent internal moisture damage in tools.
Moisture builds up inside air tools and leads to rust. Always use a water trap or airline filter. For tools with moving parts, use an automatic oiler to ensure proper lubrication. It’s safer, uses less oil, and prevents user error.
6. Air leaks cost money
Couplers like these are essential—but always check for leaks.
Even one small leak causes your compressor to cycle unnecessarily. This wastes electricity and adds wear. Use thread tape on fittings and inspect regularly to prevent energy loss.
7. HVLP spray guns save paint & protect health
HVLP spray guns reduce overspray and increase transfer efficiency.
HVLP (High Volume Low Pressure) guns spray at lower pressure, reducing paint lost into the air. They are up to 70% more efficient than high-pressure models and emit less airborne material—ideal for health & safety in workshops.
8. Use a longer air hose, not a longer power cord
Air hoses can be extended as needed—some come with couplers pre-fitted.
Air compressors consume lots of power, so keep extension cords under 10–15 metres. But air hoses can be extended safely. Install your compressor centrally and run long hoses or copper tubing around the workshop.
9. Pneumatic tools vs. power tools
- Lighter and more portable
- No risk of electrical shock
- Better power-to-weight ratio
- Longer tool life, even at DIY level
Pneumatic tools are standard in industrial settings for a reason. They’re now more accessible for DIYers thanks to affordable compressor and tool kits.
10. They’re not as expensive as you think
DIY pneumatic tools are only slightly more expensive than electric tools—but they last longer and perform better. At Adendorff, we stock a full range from light-duty DIY to semi-industrial pneumatic tools.
1. A smaller air tool doesn’t mean it uses less air.
Just because it fits in the palm of your hand does not mean it uses less air. Any spinning air tool uses plenty of air flow to drive the moving parts inside. It is true that a smaller wrench will have lower air flow than a larger heavier counterpart but it still uses enough air to deplete a direct drive compressor very quickly. To make things easy just look up the tools specifications in the user manual. MAC-AFRIC™ products will always give you the CFM or l/min number and match that to a relevant compressor size.
2. You need a 20 % larger compressor than you think you do
Shopping for a compressor on a budget can be tricky, especially when you have to balance cost with performance. It’s not just about finding the lowest price – you also need to consider how much work you plan to do and how long each session will last. Many DIYers and semi-industrial users find themselves choosing between compressors that vary in price, size, and duty cycle. Understanding how these factors work together is key to making the right decision.
Most DIY and semi-industrial compressors have a duty cycle of 60 to 80%. This means that for every 10 minutes of running time, the compressor needs 4 minutes to cool down to avoid overheating. The duty cycle can vary depending on factors like room temperature, humidity, and how hard the compressor is working, so it’s important to consider your environment when choosing a model.
To determine the right compressor size for your needs, start by looking at the air tools you'll be using. Each tool has a specific CFM (cubic feet per minute) air requirement, which indicates how much air it needs to operate effectively. A good rule of thumb is to add about 20% to the CFM rating of your air tool to ensure your compressor can supply enough air. This buffer allows the compressor to run efficiently without overworking, giving it time to cool down during heavy usage and extended workloads.
If you're unsure where to start, browse our air compressor range to find a model that meets both your performance needs and budget. Whether you need a small, budget-friendly option for light tasks or a larger, more powerful compressor for industrial use, we offer a variety of air compressors to suit every need and price point.
3. DIY compressors are not workshop machines.
Picking up the cheapest compressor you can get your hands on will always cost you more money in the long run. Smaller machines such as this have lower duty cycles and will not last long enough in a workshop environment. It’s always advised to get at least a belt driven machine as a bare minimum. Also take your CFM usage into account and work out how large of a machine you need. Adendorff stock machines of all sizes from direct drive up to the larger 380V semi-industrial compressors.
DIY COMPRESSORS = DIRECT DRIVE, BELT DRIVE – ENTRY SEMI INDUSTRIAL, 380V BELT DRIVE – SEMI INDUSTRIAL.
4. Air Pressure is important
Almost any compressor with a tank will supply you with 8 bar of air pressure (8 bar = 8 times the atmospherically air pressure of earth at sea level). However most air tools do not require anywhere near that amount of pressure. Most air tools will always have a mark on them near the input of the air pressure required, overdo this pressure too much and your pneumatic tool’s lifetime will be affected. Stick to the recommended air pressure and the tool will actually perform better than at a higher pressure and last longer. This is especially true with Spray Guns, the wrong air pressure means your spray jobs might turn out badly.
5. Using moving air tools without an filter is looking for trouble
Airline filters AKA Water traps are vital to the care of any pneumatic tool. It removes most of the humidity (moisture) from the air in the line. This results in less moisture build up inside the air tool and reduces rust build up. Not using equipment like this is ill advised and could result in a void warranty. So always use one even if it’s a small direct water filter. All air tools with moving parts require consistent lubrication just like a car engine. Problem is they do not have storage for the oil so it needs to be fed into the tool directly with the air that powers the tool. A lot of technicians would lubricate the tool by simply dripping oil into the air inlet, problem with this is you have no record or control on how frequently you have to do this. The moment you forget or someone goes on break the record is lost and this result in an air tool running without proper lubrication. Auto oilers such as the one picture above will constantly and evenly oil the tool, this also uses less oil than adding by hand.
6. Air leakage is costing you money (TOO MUCH OF IT)
One every single air outlet or inlet you will see a coupler similar to the pictured above. However you would notice in many workshops they are not fitted with thread tape. Applying thread tape to your air connectors are vital to prevent air leaks. Air leaks are a problem, they affect the resulting pressure of your outlets but most importantly leaks cost power and affect compressor lifetime. When a line is leaking (only 1 leak will do) this will continually empty the receiver of the compressor, once around 6 bar is reached the compressor will auto switch on to get back to 8 bar. The compressor has run now completely unnecessarily while no-one is using your compressor. Now add this up to once or twice a day for a year and you can imagine the energy wasted.
7. HVLP spray guns saves you money keeps you healthy
HVLP (high volume low pressure) spray guns like the one pictured above spray a much thicker higher volume of paint at a much lower pressure. This result in larger material (paint) droplets being thrown onto the surface. This means less of the material is lost into the atmosphere. It is known that conventional high pressure guns result in up to 80 percent material loss to atmosphere. HVLP guns are nearly 70 percent more affective in material transfer than older high pressure guns. Because there is so much less material drifting around in the air around the work area, less of it is exposed to the user or anyone nearby. This means that in many industries where health & safety is a factor HVLP or LVLP guns are a preferred and in some cases a mandatory choice.
8. Make your air hose longer not your compressor wire
Air compressors are energy hungry machines and require quite a bit of power to get going so its advised to keep your power cord to a minimum length (10 – 15 meters at the most @ 2.5 mm thick). You hose however does not fall under this restriction so you can easily get a longer hose to distribute air flow access throughout you workshop. If you have one stationary larger compressor install it in a well ventilated area to the middle of your workshop and distribute the air connections from there. You can also use copper tubing instead of the less heavy duty rubber hosing for a more permanent fixture.
9. The benefits of pneumatic tools vs Power tools
- Lightweight
- Safer (no electrical supply to short circuit you)
- Higher power to weight ratio. Requires smaller lightweight tool to complete the same task.
- A DIY grade pneumatic tool will last longer than a DIY grade power tool. The same applies to higher industrial grade ones.
Pneumatic tools have always been ubiquitous to the industrial trade but is now becoming more frequently DIY used tool.
10. They are not expensive (at least on the DIY level)
DIY grade pneumatic tools are only slightly more expensive than DIY grade power tools but they will always outlast and outperform them. It’s a common misconception that pneumatic tools come with higher costs. At Adendorff Machinery we keep a wide range of pneumatic tool ranging from DIY to semi-industrial grade.
Thank you for reading feel free to share on Facebook via the link below
Have a great Day